CLS 6500 User manual

(EN)

CLS 6500

Installation manual

Dinacell Electrónica S.L.

1 Introduction

1.1 Product Description

Weighing system specifically designed for use in silos, incorporating a high-precision load cell installed under a support with an optimized tilting angle. This design ensures perfect adaptation of the cell, allowing easy installation and replacement with minimal displacement of 10 mm, without the need to significantly lift the silo structure. The support is attached directly to the silo leg, making it easy to implement even in already constructed silos.

The system includes a ground-anchored base that acts as an anti-tip feature, improving stability and safety. In addition, it features a protection system against electrical discharges, a UV-resistant housing, and effective sealing against high-pressure water jets, ensuring long-lasting performance in demanding environments.

Weight Display

For applications requiring high accuracy in silo weighing, our solution includes the installation of CLS cells at each support point, with signals centralized in a junction box. This system allows the transmission of all measurements through a single cable to the measuring device, ensuring reliability, ease of installation, and simplified maintenance.

Junction box Weighing device

23 1789 456 100 0000 000 0 0 TAAAxLLNAAARRLMMOG--12 ERROR Monitor MLS20 Series Four-leg silo installation diagram Percentage Level Display

f the need is only to display a percentage value to approximately manage the silo content, we offer a simpler alternative that requires only a single cell connected to the appropriate measuring device.

Weighing device It is advisable to use our CNS model with connectivity to the application, which has a c specific filter for viewing the percentage level.

1.2 Compatible Legs

Flat-profile leg with a minimum thickness ≥3 mm Round-profile legs with a minimum thickness ≥3 mm Under development

1.3 Installationsanforderungen

Min. 320mm 90o

Min. 200mm

6x 6x 6x 6x 2x 1x 2x

2x 2x 1x 1x 1x 2x 2x 2x

1x 1x 1x 1x 1x

1x 1x 1x 2X 2X 1x 1x 1x

4 160130 351400 484130 )21M 219-NID( )A8976-NID( 584130 281920 928420 )6M 339-NID( 910000 )21M A521-NID( 002000 576620 )6M 439-NID( 021130 546620 )3296-NID( 737420 427620 198820 166820 790100 411130 )1136 -NID( 351400 111100 )49-NID( )4M 219-NID( 974130 658820 346620 350200 )4M A521-NID( 084130 450200 713800 )4M 439-NID( 700130 184130 Installation Elements 2.1 Package Contents 2.2 Installation Tool Contents Please note that the installation tool is not included with the CLS load cell. However, its acquisition is recommended to facilitate the installation process and ensure proper cell placement.

2.3 Required Tools

Pliers Metal drill bit Ø12 Cable guide Socket wrench set

Rubber mallet Hammer drill Concrete drill bit Ø16 Set of Allen keys

2.4 Recommended Tools for Installation

Impact wrench Torque wrench Metal drill bits Ø8 - Ø13 Flexible corrugated tube

Metal clamps Clamp screw Set of open-end wrenches

3 Step-by-step installation

026675

029182

1x ø12

031061

031120 73 N.m

7 mm03< >10mm <10mm mm03< 1 Adjustment Based on Leg Support It is necessary to insert a washer if there is a gap between the bracket and the silo leg It is necessary to cut off the excess bracket as long as it does not affect the safety of the structure, in order to attach the load cell to the silo leg

004153

026643

1x

90o

4x

9 15mm 6 7 026675 427620 5 6 3 4 031114

2x

120mm

10 10mm 8 9 Loosen the screws of the installation tool until the load cell base rests on the floor plane, then proceed with the next step.

10

2x

50 Nm

11 713800 11

12

13

000200

024829 004153

12

14

1 9 8 8 2 0

13 737420 790100 )deR( .cxE + )kcalB( .cxE - )neerG( langiS + )etihW( langiS - )DNG( dleihS

15

002054

024829

16

028661

028856

14

17

18

15 484130 If the anti-tip rod is misaligned and touches the silo base, enlarge the hole using the cutting crown of the installation tool to prevent any interference with the weight measurement. To ensure precise alignment of the crown cut with the rod, the tool comes with centering rings in various sizes for optimal fit. Secure the locking nut onto the anti-tip rod, ensuring it does not make contact with the silo base. If the nut is smaller than the hole, insert a larger diameter washer between the base and the nut, making sure there is no direct contact with the nut.

For more information

www.dinacell.com

Document Ref: D2402-02 Publication Date: 01/04/2025